PERFORMANCE GUIDE
|
FILM PROPERTIES
Chemical Resistance
Heat Resistance
Water Resistance
|
Resistant against splashes and spillage of common acid, alkalis, solvent and salt solutions.
Can be used on heated surfaces up to 110°C.
Excellent.
|
THEORECTICAL COVERAGE
|
A guide to the theoretical coverage which can be achieved under normal conditions is 10m²/L for brush application and 4m²/L for spray application.
|
PRODUCT DATA
|
COMPOSITION
(nominal)
|
Pigment : Lightfast Non-Lead Pigments and Mineral Extenders.
Blinder : PVA Copolymer Emulsion.
Solvent : Water.
|
VOLUME SOLIDS
|
White 35% (nominal), other colours will vary
|
|
FLASH POINT
|
Base and Activator 23°C.
|
|
POT LIFE
|
Up to 5 hours at 30°C
|
APPLICATION
|
THINNING
Brush or Roller
Conventional Spray
Airless Spray
|
Ready for use
Add up to 1 part of Dulux Thinner 850 - 11 or T10 to 20 parts of paint (5%).
Add up to 1 part of Dulux Thinner 850 - 11 or T10 to 20 parts of paint (5%).
|
SPRAY RECOMMENDATIONS
Conventional Spray
Airless Spray
|
A typical recommendation for Conventional Spray application is a minimum atomizing pressure on paint of 3.5kg/cm² (50 ib/sq in), with a fluid pressure of 0.7kg/cm² (10 ib/sq in) with a spray nozzle size of 0.75 mm (30 thous).
A typical recommendation for Airless Spray application is a minimum working pressure on paint of 140kg/cm² (2000 ib/sq in) with a spray tip of 0.53mm (21 thou) at an angle of 80°
|
DRYING TIMES
Recoat
Full Cure
|
Single coat at standard thickness:
6 - 48 hours
7 days. The full system must be allowed to cure for 7 days at 25°C before putting into service. Please note that the reaction of epoxies commences immediately the two components are mixed. This reaction is temperature related and so the curing time will be approximately halved by a 10°C decrease in temperature.
|
CLEANING UP
|
Clean all equipment with Dulux Thinner 850 - 761 or 850 - 11.
|
FILM THICKNESS
|
|
Brush or Roller
Wet: 100 microns
Dry: 70 microns
|
Airless Spray
Wet: 250 microns
Dry: 175 microns
|
|
|
   
|
PRE - APPLICATION
|
SURFACE PREPARATION
|
Surfaces must be sound, clean, dry and free from all defective or poorly adhering material, dirt, grease or wax and be thoroughly rubbed down using a suitable abrasive paper and dusted off. If after thorough preparation, surfaces remain powdery, seal with one coat of an appropriate Primer (see below).
|
SURFACE PREPARATION
|
After suitable surface preparation the normal recommendation is to apply two coats of Dulux Coal Tar Epoxy Finish applied to the recommended film thickness. It is important to ensure that the substrate temperature is at least 3°C above dew point. The minimum temperature for application is 10°C. Relative humidity should not exceed 85%.
|
|
 
|
PRECAUTION
|
SAFETY, HEALTHY AND ENVIRONMENTAL INFORMATION
|
FLAMMABLE
Limited evidence of a carcinogenic effect.
Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Repeated exposure may cause skin dryness or cracking.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
If swallowed seek medical advice immediately and show this container or label.
If swallowed, rinse mouth with water (Only if person is conscious).
Keep away from food, drinks, animal feed and out of the reach of children.
Keep away from combustible material.
Container must be stored in a cool and shaded place.
It must be tightly closed in a secure, upright position.
Do not breathe dust.
Work in a well-ventilated area and do not breathe in vapour or spray.
A suitable mask should be worn during sanding
When applying paint, wear suitable protective clothing, gloves and eye/face protection.
In case of fire use foam, dry powder, AFFF, CO2 - Never use water.
In case of a spillage, contain and collect spillage using sand or earth and do not empty into watercourses, drains or the environment.
Dispose of any paint waste in accordance with the appropriate Environmental Quality Regulations.
Refer to Dulux Product Safety Data Sheet for further details.
In case of emergency, refer to Emergency Incident Response Hotline 1800 80 6187.
|
|
      
|
