PERFORMANCE GUIDE
|
FILM PROPERTIES
Chemicalr Resistance
Heat Resistance
Water Resistance
|
Excellent against splashes and spillage of common acids, alkalis, solvents, and salt solutions.
Can be used on heated surfaces up to 110°C.
Excellent. |
THEORECTICAL COVERAGE
|
A guide to the theoretical coverage which can be achieved under normal conditions is 6.7 - 10 m²/L.
|
PRODUCT DATA
|
COMPOSITION
(nominal)
|
Pigment : Lightfast Non-Lead Pigments and Inert Mineral Extenders.
Blinder : Polyamide Cured Epoxy.
Solvent : Alcohol and Aromatic Hydrocarbon.
|
VOLUME SOLIDS
|
50% (nominal).
|
FLASH POINT
|
22°C.
|
POT LIFE
|
Up to 6 hours at 30°C.
|
APPLICATION
|
MIXING RATIO
|
7 parts Base to 1 part Activator by volume.
|
THINNING
Brush or Roller
Conventional Spray
Airless Spray
|
Add up to 1 part of Dulux Thinner 850 - 761 to 10 parts of paint (10%).
Add up to 1 part of Dulux Thinner 850 - 761 to 10 parts of paint (10%).
Add up to 1 part of Dulux Thinner 850 - 761 to 10 parts of paint (10%).
|
SPRAY RECOMMENDATIONS
Conventional Spray
Airless Spray
|
Satisfactory through most equipment.
A typical set up for airless spray application is a minimum working pressure on paint of 140kg/cm² (2000 lb/sq in) with a spray tip size 0.43 - 0.58mm (17 -23 thou) and a spray tip angle of 65°.
|
SPRAY NOTES
|
It is important that the Base and the Activator are at a minimum temperature of 15°C when mixed for satisfactory spray application.
|
CURING TIMES
|
Single coat at standard thickness:
|
Recoat At 30°C
Full Cure
|
6 hours minimum.
7 days
Please note that the reaction of epoxies commences immediately the two components are mixed. This reaction is temperature related and so the curing time will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.
|
CLEANING UP
|
Clean all equipment with Dulux Thinner 850 - 761 immediately after use.
|
FILM THICKNESS
|
Wet: 100 - 150 micro-metres.
Dry: 50 - 75 micro-metres..
|
|
   
|
PRE - APPLICATION
|
SURFACE PREPARATION
|
Surfaces generally must be clean, dry, free from all defective or poorly adhering material, dirt, grease, wax etc.
Steel surfaces should be blast-cleaned to BS 7079 Part A1: 1989. Sa 2.5 to give an appropriate surface profile.
|
SYSTEM INFORMATION
Metal
Wood and Masonry
|
PRIMER (1 COAT)
Dulux Epoxy Zinc Phosphate Primer (A580 - 16252)
Dulux Epoxy Primer Off White A580 - PJ - 0529
|
FINISH (2 COATS)
Dulux Epoxy Chemical Resistant Finish (A430)
|
|
|
Note: It is important to ensure that the substrate temperature is at least 3°C above dew point. The minimum temperature for application is 10°C. Relative humidity should not exceed 85%. Where primer or intermediate coat of Dulux Epoxy Chemical Resistant Finish has been left exposed over a period of time it will be necessary to thoroughly prepare the surface by removing all dirt, grease oil, wax, rust, salts etc before the overpainting. Where rusting of peaks has occurred on blast cleaned steel, flash blasting or thorough manual preparation followed by spot priming with an appropriate primer will be required.
|
|
 
|
PRECAUTION
|
SAFETY, HEALTHY AND ENVIRONMENTAL INFORMATION
|
FLAMMABLE
Harmful by inhalation and in contact with skin.
Irritating to eye.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
If swallowed seek medical advice immediately and show this container or label.
If swallowed, rinse mouth with water (Only if person is conscious).
Keep away from food, drinks, animal feed and out of the reach of children.
Keep away from combustible material.
Container must be stored in a cool and shaded place.
It must be tightly closed in a secure, upright position.
Do not breathe dust.
Work in a well-ventilated area and do not breathe in vapour or spray.
When applying paint, wear suitable protective clothing, gloves and eye/face protection.
In case of fire use foam, dry powder, AFFF, CO2 - Never use water.
In case of a spillage, contain and collect spillage using sand or earth and do not empty into watercourses, drains or the environment.
Dispose of any paint waste in accordance with the appropriate Environmental Quality Regulations
Refer to Dulux Product Safety Data Sheet for further details.
In case of emergency, refer to Emergency Incident Response Hotline 1800 80 6187.
|
|
      
|
