PERFORMANCE GUIDE
|
FILM PROPERTIES
Chemical Resistance
Heat Resistance
Water Resistance
|
Resistance against splashes and spillage of common acids, alkalis, solvents, and salt solutions.
Can be used on heated surfaces up to 110°C.
Excellent.
|
THEORECTICAL COVERAGE
|
A guide to the theoretical coverage which can be achieved under normal conditions is 3.6 - 7.2 m²/L.
|
PRODUCT DATA
|
COMPOSITION
(nominal)
|
Pigment : Zinc Phosphate, Non-Lead Pigments and Inert Mineral Extenders.
Blinder : Amine Adduct Cured Epoxy.
Solvent : Ketone, Toluene and Alcohol.
|
VOLUME SOLIDS
|
54% (nominal).
|
FLASH POINT
|
Base and Activator - 22°C.
|
POT LIFE
|
Up to 6 hours at 30°C.
|
APPLICATION
|
MIXING RATIO
|
11.5 parts Base to 1 part Activator by volume.
|
THINNING
|
Add up to 1 part of Dulux Thinner 850 - 761 or 850 - 11 to 20 parts of paint (5%).
|
SPRAY RECOMMENDATIONS
Airless Spray
|
A typical set up for airless spray application is a minimum working pressure on paint of 140kg/cm² (2000 lb/sq in) with a spray tip size 0.38 - 0.53mm (15 - 21 thou) and a spray tip angle of 20° - 45°.
|
SPRAY NOTES
|
It is important that the Base and the Activator are at the minimum temperature of 15°C when mixed for satisfactory spray application. |
CURING TIMES
Recoat At 30°
Full Cure
|
Single coat at standard thickness:
6 hours minimum.
7 days.
Please note that the reaction of epoxies commences immediately after the two components are mixed. This reaction is temperature related and so the curing time will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.
|
|
CLEANING UP
|
Clean all equipment with Dulux Thinner 850 - 761 or 850 - 11 immediately after use.
|
FILM THICKNESS
|
Wet: 140 - 280 micro-metres
Dry: 75 - 150 micro-metres.
|
|
   
|
PRE - APPLICATION
|
SURFACE PREPARATION
|
For optimum performance, blast clean to BS 7079 Part A1: 1989 Sa 2.5 to give an appropriate surface profile.
|
SYSTEM INFORMATION
Metal
|
PRIMER (1 COAT)
Dulux Epoxy Zinc Phosphate Primer (A580 - 16252)
|
FINISH (2 COATS)
Dulux Hi Build Epoxy Tank Coating (A580)
|
|
|
It is important to ensure that the substrate temperature is at least 3°C above dew point.
The minimum temperature for application is 10°C. Relative humidity should not exceed 85%.
Note: Where primer has been left exposed over a period of time, it will be necessary to thoroughly prepare the surface by removing all dirt, grease, oil, wax, rust, salts etc before the overpainting. Where rusting of peaks has occurred on blast cleaned steel, flash blasting or thorough manual preparation followed by spot priming with an appropriate primer will be required.
|
|
  
|
PRECAUTION
|
SAFETY, HEALTHY AND ENVIRONMENTAL INFORMATION
|
HIGHLY FLAMMABLE
Harmful by inhalation and in contact with skin.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
If swallowed seek medical advice immediately and show this container or label.
Keep away from food, drinks, animal feed and out of the reach of children.
Keep away from combustible material.
Container must be stored in a cool and shaded place.
It must be tightly closed in a secure, upright position.
Take precautionary measures against static discharges.
Do not breathe dust.
Work in a well-ventilated area and do not breathe in vapour or spray.
When applying paint, wear suitable protective clothing, gloves and eye/face protection.
In case of fire use foam, dry powder, AFFF, CO2 - Never use water.
In case of a spillage, contain and collect spillage using sand or earth and do not empty into watercourses, drains or the environment.
Dispose of any paint waste in accordance with the appropriate Environmental Quality Regulations.
Refer to Dulux Product Safety Data Sheet for further details.
In case of emergency, refer to Emergency Incident Response Hotline 1800 80 6187.
|
|
      
|
