ICI Dulux - Products (TRU-GLAZE-WB(TM) 4030 Waterborne Epoxy Primer)

home | about us | careers | contact us

Colour Themes

Products

Support, Tips & Tools

Promotional
News & Events



Products
Eco-friendly range
Decorative Paints
Interior Wall/Ceiling
Exterior Wall/Roof
Woods/Metal/Floor
High Performance Paints
Interior
Exterior
Product's Brochures
Download Colour Inspirations 2010/2011 Download Dulux Warnai Musim Perayaan Ini Download Dulux Weathershield Keep Cool Brochure 2010 Download Colour Ideas

Home : Products : High Performance Paints : Interior : TRU-GLAZE-WB^TM 4030 Waterborne Epoxy Primer

TRU-GLAZE-WB^TM 4030 D4030-B6130 (High Performance - Waterborne)
Waterborne Epoxy Primer

A high performance, two-package, chemically-cured, waterborne epoxy rust inhibitive primer.

USAGE
Suitable for interior and exterior steel, aluminium and certain galvanized metal surfaces. Also used over concrete, masonry, glazed brick or ceramic tile. Features excellent adhesion, corrosion resistance, and good resistance to splash, spillage or fumes of a wide range of chemicals. May be topcoated with epoxy, urethane, alkyd, or latex coatings.

Special Qualifications
Suitable for use on structural surfaces of surfaces where there is a possibility of incidental food contact in commercial food preparation establishments, food processing plants and federally inspected meat and poultry plants. USDA no longer requires or furnishes product certification letters.

BENEFITS

Excellent adhesion.
Excellent corrosion resistance.
Lead free pigmentation.
Light gray colour permits good finish coat hiding.
Excellent recoatibility with all types of finishes.
Low colour.
High flash point with Class A low flame spread rate.
Low VOC.
Performance alternate for Federal Specification MIL-P-23377F (TYPE1, CLASS 3).

PACK SIZE 5 litres units comprising Base: 4 litres and Converter: 1 litre.

COLOUR RANGE Light Grey.

Download Product Information

PERFORMANCE GUIDE
FILM PROPERTIES Adhesion Hardness Flexibility Humidity Resistance	Excellent Good Excellent Excellent
PRODUCT DATA
COMPOSITION (nominal)	Pigment : Lightfast Non-Lead Pigments and Mineral Extenders. Binder : Polyamide Cured Epoxy. Solvent : Aromatic Hydrocarbon and Alcohol.
Weight/Litre	1.37 kg/L
VOC (EPA 24)	193 g/L
Volume Solids	47% ± 1%
Theorectical Coverage	19m²/L at 25 µm dry.
Practical Coverage	Apply at 5 - 6 m²/L on steel. Actual coverage may vary depending on substrate and application method. When applying by spray, losses due to overspray can be heavy on narrow sections.
Service Temperature Limits	121°C in air.
Flame Spread Rating	Class A (0-25) over non-combustible surfaces.
Shelf Life	1 year minimum - unopened.
Mix Ratio By Volume	4 (Base) : 1 (Converter)
Induction Time	30 minutes.
Pot Life	Up to 8 hours at 25°C.
Flash Point	93°C.
APPLICATION
THINNING	Thinning is not normally required. However, if necessary add up to 1 part of water to 10 parts of paint (10%).
SPRAY RECOMMENDATIONS Conventional Spray Airless Spray	Satisfactory through most equipment. A typical set up for airless spray application is a minimum working pressure on paint of 3000psi (207 bars) with a spray tip size 0.19".
CURING TIMES Recoat 25°C Hard Dry	Single coat at standard thickness: Overnight - 1 Week. 5 days.
CLEANING UP	Clean immediately after use with warm, soapy water. Rinse pumps and hoses with T-10, thinner or xylene after cleaning.
FILM THICKNESS	Wet: 100 - 200 microns. Dry: 50 - 100 microns.
PRE - APPLICATION
SURFACE PREPARATION	All surfaces must be sound, clean, dry, and free of oil, grease, dirt, mildew, form release agents, curing compounds, efflorescence, loose and flaking paint and other foreign substances.
SURFACE INFORMATION NEW SURFACES Steel Aluminium Galvanized Metal Concrete, Plaster and Masonry	Best results are obtained over a surface sandblasted to a commercial Blast (SSPC-SP6). Performance over hand or powertool cleaned surfaces is dependent on the degree of cleaning. Prine with this product. If rust staining occurs, apply a second coat of this product. Primer with this product. Prime with this product (must be test patched for adhesion prior to use due to the high variability of surface treatments). Cure at least 30 days before painting. pH must be 10.0 or lower. Remove laitance and roughen usually slick poured or precast concrete by acid etching or sandsweeping. Following acid manufacturer's application and safely instructions. Rinse thoroughly with water and allow to dry. Remove loose aggregate.
PREVIOUSLY PAINTED SURFACES	Primer with this product. The waterborne components of this product generally allow use over most old coatings. Old coatings should be tested for lifting. If they lift, remove them. Wash to remove contaminants. Rinse thoroughly with water and allow to dry. Dull glossy areas with light sanding. Remove sanding dust. Remove loose paint. Prime bare areas with primer specified under New Surfaces.
PRECAUTION
SAFETY, HEALTHY AND ENVIRONMENTAL INFORMATION	D4030-BASE Avoid contact with skin/eyes FLAMMABLE Irritating to eyes, respiratory system and skin. Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. May cause sensitisation by skin contact. Avoid contact with skin/eyes. If swallowed seek medical advice immediately and show this container or label. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes of paint from skin, use soap and water or a recognised cleanser. Contains: ALIPHATIC GLYCIDYLETHER. May produce an allergic reaction. Keep away from food, drinks, animal feed and out of the reach of children. Keep away from combustible material. Container must be stored in a cool, shaded place and tightly closed in a secure, upright position. Take precautionary measures against static discharges. Work in a well-ventilated area and do not breathe in vapour or spray. When applying paint, wear suitable protective clothing, gloves and eye/face protection. In case of fire use foam, dry powder, AFFF, CO2 - Never use water. In case of a spillage, contain and collect spillage using sand or earth and do not empty into watercourses, drains or the environment. Dispose of any paint waste in accordance with the appropriate Environmental Quality Regulations. Refer to Product Safety Data Sheet for further details. In case of emergency, refer to Emergency Incident Response Hotline 1800 80 6187. D4030-CONVERTER IRRITANT FLAMMABLE Harmful by aquatic organisms, may cause long-term adverse effects in the aquatic environment. Irritating to eyes, respiratory system and skin. Avoid contact with skin/eyes. May cause sensitisation by skin contact. If swallowed seek medical advice immediately and show this container or label. If swallowed, rinse mouth with water (Only if the person is conscious). In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes of paint from skin, use soap and water or a recognised cleanser. Keep away from food, drinks, animal feed and out of the reach of children., Keep away from combustible material. Container must be stored in a cool, shaded place and tightly closed in a secure, upright position. Take precautionary measures against static discharges. Work in a well-ventilated area and do not breathe in vapour or spray. When applying paint, wear suitable protective clothing, gloves and eye/face protection. In case of fire use foam, dry powder, AFFF, CO2 - Never use water. In case of a spillage, contain and collect spillage using sand or earth and do not empty into watercourses, drains or the environment. Dispose of any paint waste in accordance with the appropriate Environmental Quality Regulations. Refer to Product Safety Data Sheet for further details. In case of emergency, refer to Emergency Incident Response Hotline 1800 80 6187.