|
|
|
Home : Trade
Professional : Trade Products
(High Performance Paints) : Dulux Sterishield Waterborne Epoxy
Gloss Coating
|
|
Dulux STERISHIELDTM D4408-B Line (High Performance -
Solventborne)
WATERBORNE EPOXY GLOSS COATING
|
|
A high perfomance, two-component chemically-cured
waterborne gloss epoxy coating for use as a hard, durable high
performance architectural coating (HIPAC)
USAGE
For use on interior properly prepared poured concrete, concrete
block, drywall, metal, wood. Ideal for hard usage areas of
schools, hospitals, restaurants, public buildings and factories.
May be used in areas subject to continuous high moisture such as
shower rooms.
Special Qualifications
Suitable for use on structural surfaces where there is a
possibility of incidental food contact in commercial food
preparation establishments, food processing plants and federally
inspected meat and poultry plants. USDA no longer requires or
furnishes product certification letters.
BENEFITS
- Chemical and stain resistant.
- Resists splash and spillage of alkalis, salts,
moisture, oils, grease, foodstuffs, and detergents.
- Abrasion resistant.
- Low odor and high flash point.
- Use over alkyd, latex or epoxy coatings.
- Long lasting tile-like finish.
- Easily washed and cleaned.
- Low VOC.
- Performance alternate for Federal Specifications TT -
C535B (Type II) and TT - C - 550C (Class A).
PACK SIZE 5 litre units comprising Base: 2.5 litre
and Converter:2.5 litre
COLOUR RANGE White and custom colours
|
Download Product Data Information
|
PERFORMANCE
GUIDE
FILM PROPERTIES |
Abrasion Resistance
Pencil Hardness
Flexibility
Impact Resistance
Water Resistance
Chemical/Stain Resistance
|
Good
Good
Excellent
Excellent
Excellent
Excellent
|
| PRODUCT
DATA |
COMPOSITION
(nominal)
Weight/Litre
VOC (EPA 24)
Volume Solids
Theorectical Coverage
Service Temperature Limit
Flame Spread Rating
Shelf Life
Mix Ratio By Volume
Induction Time
Pot Life
Flash Point |
Pigment :
Lightfast Non-Lead Pigments and Mineral Extenders.
Blinder : Polyamide Cured Epoxy..
Solvent : Aromatic Hydrocarbon and Alcohol.
1.21 kg/L - varies with colour
206 g/L - varies with colour
43% ± 1% - varies with colour
A guide to the theorectical coverage which can be achieved
under normal conditions is 3.44 - 8.6m²/L. When applying
by spray, looses due to overspray can be heavy on narrow
sections.
121°C in air.
Class A (0-25) over non-combustible surfaces.
1 year minimum - unopened.
4 (Base) : 1 (Converter)
30 minutes.
Up to 8 hours at 25°C.
96°C.
|
| APPLICATION
|
THINNING
|
Thinning is not
normally required. However, if necessary add up to 1 part of
water to 10 parts of paint (10%). |
SPRAY RECOMMENDATIONS
Conventional Spray
Airless Spray
|
Satisfactory through most equipment.
A typical set up for airless spray application would be a
minimum working pressure on paint of 3000 psi (207 bars) with
a spray tip size 0.015".
|
CURING TIMES
Recoat at 25°C
Full cure
|
Single coat at
standard thickness:
Overnight.
7 days.
|
CLEANING UP
|
Clean
immediately after use with warm, soapy water. Rinse pumps and
hoses with xylene after cleaning.
|
FILM THICKNESS
|
Wet: 115 - 290
microns
Dry: 50 - 125 microns
|
| PRE -
APPLICATION |
SURFACE PREPARATION
|
All surfaces
must be sound, clean, dry, and free of oils, grease, dirt,
mildew, form release agents, curing compounds, efflorescense,
loose and flaking paint and other foreign matter.
|
SYSTEM INFORMATION NEW SURFACES
Concrete, Plaster, and Masonry
Drywall
Wood
Steel
Galvanized Metal and Aluminium
Glazed Brick, Ceramic Tile and Fiberglass
PREVIOUSLY PAINTED SURFACES
|
Cure at least 30 days before painting. pH must be 10.0 or
lower. Remove laitance and roughen usually slick poured or
precast concrete by acid etching or sandsweeping. Follow
acid manufacturer's application and safety instructions.
Rinse thoroughly with water and allow to dry. Remove loose
aggregate Prime with this product thinned 8:1 with water or
prime with waterborne epoxy primer. Dry overnight to recoat.
Fill concrete block in areas not subject to moisture with
latex filler. In moisture prone areas, fill with this
product. Fillers must dry overnight before coating.
Prime with this product or waterborne epoxy primer.
Prime with this product.
Prime with waterborne epoxy primer.
Prime with waterborne epoxy primer.
Scuff sand and prime with waterborne epoxy primer.
The waterborne components of this product generally allow
use over most old coatings. Old coatings should be tested
for lifting. If they lift, remove them. Wash to remove
contaminants. Rinse thoroughly with water and allow to dry.
Dull glossy areas by light sanding. Remove sanding dust.
Remove loose paint. Prime bare areas with primer specified
under New Surfaces. |
|
| PRECAUTION
|
SAFETY, HEALTHY AND ENVIRONMENTAL INFORMATION
|
D4408B-BASE
IRRITANT
Irritating to eyes, respiratory system and skin.
Avoid contact with skin/eyes.
May cause sensitisation by skin contact.
If swallowed seek medical advice immediately and show this
container or label.
If swallowed, rinse mouth with water (Only if the person is
conscious).
In case of contact with eyes, rinse immediately with plenty of
water or a recognised cleanser.
To remove splashes of paint from skin, use soap and water or a
recognised cleanser.
Keep away from food, drinks, animal feed and out of the reach
of children.
Keep away from combustible material.
Container must be stored in a cool, shaded place and tightly
closed in a secure, upright position.
Take precautionary measures against static discharges.
Work in a well ventilated area and do not breathe in vapour,
spray or dust.
When applying paint, wear suitable protective clothing, gloves
and eye/face protection.
In case of fire use foam, dry powder, AFFF, CO2 - Never use
water.
In case of a spillage, contain and collect spillage using sand
or earth and do not empty into water courses, drains or the
environment.
Dispose of any paint waste in accordance with the appropriate
Environmental Quality Regulations.
Refer to Product Safety Data Sheet for further details.
In case of emergency, refer to Emergency Incident Response
Hotline 1800 80 6187.
DD4408B-CONVERTER
Avoid contact with skin/eyes.
If swallowed seek medical advice immediately and show this
container or label.
In case of contact with eyes, rinse immediately with plenty of
water and seek medical advice
To remove splashes of paint from skin, use soap and water or a
recognised cleanser.
Contains: ALIPHATIC GLYCIDYLETHER. May produce an allergic
reaction.
Keep away from food, drinks, animal feed and out of the reach
of children
Keep away from combustible material.
Container must be stored in a cool, shade place and tightly
closed in a secure, upright position.
Take precautionary measures against static discharges.
Work in a well ventilated area and do not breathe in vapour,
spray or dust.
When applying paint, wear suitable protective clothing, gloves
and eye/face protection.
In case of fire use foam, dry powder, AFFF, CO2 - Never use
water.
In case of a spillage, contain and collect spillage using sand
or earth and do not empty into water courses, drains or the
environment.
Dispose of any paint waste in accordance with the appropriate
Environmental Quality Regulations.
Refer to Product Safety Data Sheet for further details.
In case of emergency, refer to Emergency Incident Response
Hotline 1800 80 6187.
|
|
|
|
